What You'll Need 37-gallon heavy-duty trashcan with lid / forty 10-1/2-inch x 7-inch x 3-1/2-inch tumbled rock bricks / twenty-six 7-inch x 7-inch x 3-1/2-inch tumbled stone bricks / seventeen 7-inch x 3-1/2-inch x 1-3/4-inch tumbled stone bricks / 1/2 HP Sump pump with 1-1/4-inch hose / 2 12-inch lengths 2-inch pvc pipe / 22-inch plastic flower box / 1-1/4-inch bulkhead / 1-1/4-inch ribbon adapter / two 1-1/4-inch street 90-degree elbow pipes / 1-1/2-inch x 48-inch perforated angle iron / 22-inch x 39-inch piece pond liner / 26-inch x 7-inch aluminum flashing / silicone sealant / 2 1-1/4-inch hose barbs with clamps / 24-inch x 24-inch metal lath or heavy display / 24-inch x 48-inch slate slab / shovel / flat / tape gauge / drill using 2-1/2-inch and 1-1/4-inch hole saws / tin snips / utility knife / jigsaw
Dig Hole and Place Reservoir Select a location and orientation for your fountain. Check with utility companies before digging, then use a shovel to dig out a hole just large enough to hold your 37-gallon trash can, leaving an increase of about two inches at the surface. Use a level to ensure can rests calmly. Fill any gaps and cover with lid while functioning to keep out dirt. This trashcan will serve as a reservoir where water will be drawn and returned when the fountain is operating.
Level Ground Utilize dirt out of paver or hole base to level the ground around the reservoir and tamp down completely you can find out more. It's important that the ground be level and firm to set up a sturdy basis for your own fountain riser.
Construct Bottom Riser Tier Using tumbled stone, make a riser tier 39-1/2 x 21 inches, with a long side resting 1 inch out of the reservoir at its midpoint. Tumbled stone located at the local hardware stone is designed to provide a number of configurations that will result in uniform dimensions. Press firmly to place grade and use a level to affirm it rests plumb and level.
Establish Pass-throughs for Water and Power Lines Eliminate the tumbled stone resting in the edge of the reservoir and then dig a 3-inch-deep trench in the reservoir into the open area within the riser Your Domain Name. Repeat this procedure on the long edge opposite the reservoir. Step down 1 inch from the lip on the reservoir at the midpoint of the riser and drill a hole using a 2-1/2-inch hole saw. This gap will be used to make a pass-through for water and electricity lines in the sump pump.
Insert Raceway Put a 12-inch span pvc throughout the drilled hole, hanging about two inches within the reservoir. Bury pipe and substitute tumbled stone over this post. Place another piece of PVC in the trench opposite the reservoir, bury and replace tumbled stone.
End Riser Add five tiers of tumbled stone, with a level to confirm the riser remains square and flat Read Full Article. Vary stone configuration of every tier to make a patchwork look. Finally, add a seventh layer, with 7-inch x 3-1/2-inch x 1-3/4-inch tumbled bricks to create a centered, half-height 24-1/2-inch-wide spillway gap facing the reservoir, as shown.
Attach Bulkhead to Diffuser Use 1-1/4-inch hole saw bit to drill a hole at the base of the flower box 3 inches from a short end. Push bulkhead though the hole and secure with nut. Attach thread adapter into the bulkhead within the box.
Assemble Diffuser Attach a road 90-degree elbow into the ribbon adapter facing the middle of the box and then complete with second street elbow facing downward here helpful site. This box will rest inside the riser and serve as a diffuser, alllowing water to pool and flow freely over the spillway to create a waterfall.
Place Sump Pump Set sump pump at the base of the reservoir (pump may be placed on a paver to reduce debris consumption, if desirable). Water will pump through the diffuser and flow across the riser, returning to the reservoir at a closed system cycle.
Thread Plumbing and Power Use a hose barb and clamp to attach hose into the sump pump article. Push the hose and power cord from the sump pump through the raceway into the riser. Gently the hose over the surface of the riser and push the power cord through the rear raceway of the riser where it can be plugged into an outlet to give power to the pump.
Shape Mounting Bracket Starting at one end of 48-inch-long perforated angle iron, mark and measure points in 5-1/2 inches, 13-1/2 inches, 34-1/2 inches and 42-1/2 inches. Using a jigsaw, cut one edge of the bracket at marked points and then fold into a rectangle with a 10-inch open gap on one side, as displayed hop over to this site. Trim edges as needed to allow a fit inside the riser go to this site. This mount will break inside the riser and can be used to support the diffuser.
Quantify Water Barrier Place the mounting bracket in the middle of a 22-inch x 39-inch piece of pond liner and mark points within each corner.
Cut Water Barrier Use a utility knife to cut a large "X" in the liner from marked points. This waterpoof sheet will be used to make a barrier between the diffuser and the riser to avoid overflow.
Insert Mounting Bracket Place mounting bracket in riser so the open side of the bracket rests on the rear of the riser and the extended border rests within the spillway (bend as needed to guarantee a secure fit).
Attach Diffuser Lay the water barrier above the mounting bracket and pass the nozzle through the gap read this post here. Twist sump pump hose tube to the bulkhead on the base of the diffuser (blossom box).
Mount Diffuser Put the diffuser inside the mounting bracket, ensuring the water barrier expands under the lip on either side. The diffuser will pitch slightly forward in the space to permit water to flow smoothly though the spillway.
Shape Scupper Along one long side of aluminum flashing, mark points 1 inch from each end. Along the opposite border, mark points 1-1/2 inches. Use a pencil to connect the things in short ends. Bend flashing 90 degrees along pencil lines. This "scupper" will break in spillway to guide water stream.
Place Scupper Center the scupper from the spillway beneath the water barrier together with the tall border at the rear of the spillway. The outer border should rest evenly along the outside border of tumbled stones.
Fill Reservoir Use a garden hose to fill the reservoir with water, stopping about an inch below the pass-though pipe.
Seal Diffuser Assembly Once desired flow is accomplished, turn pump off visit the site. Lift and drain diffuser and thoroughly dry diffuser, water barrier and scupper with a towel . Use silicone to line borders where the diffuser meets the water barrier and then press diffuser securely back in place. Turn up front border of plain water barrier, draw on a line of silicone on the top of the scupper and press on barrier back in position. The silicone acts as a seal, so maintaining components set up and preventing water from contact with the stone or flowing within the riser.
Cut Reservoir Cover Use a ribbon or utility knife to cut away half of the trashcan lid, leaving a three inch border to create a half-moon comprehensive which water can flow. Set the lid topside-down on top of the reservoir.
Cut and Place Reservoir Screen Use tin snips to cut a half-moon of lath or thick display that fulfills the edges of the trash can lid and extends at least 3 inches beyond the center of the lid check out here my review here. Place screen on lid to cover the gap. This display allows water to flow freely to the reservoir whilst limiting debris.
Place Cap Once silicone seal has completely dried, turn the pump back on to confirm water is flowing correctly. If no further adjustments are required, set a 24-inch x 48-inch slab of slate on top of the riser to cap.
Landscape It Place rocks of varying sizes across the edges of the reservoir to vague screen and include native plants around the website to accent its natural beauty. Avoid placing rocks beneath the water flow to prevent splashing that will gradually clog the machine.
Light It Up Contemplate accent lighting to showcase this beautiful fountain after twilight.
Maintenance This peaceful fountain can run fulltime or put on a timer to stream just at peak times. To maintain, assess water levels sometimes and burn as needed. Drain fountain during winter months to reduce damage to plumbing.
No comments:
Post a Comment